Brocade Communications Systems 8 Guía de instalación Pagina 179
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Electrical dangers
DANGER
Make sure that the power source circuits are properly grounded, then use the power cord
supplied with the device to connect it to the power source.
GEFAHR Stellen Sie sicher, dass die Stromkreise ordnungsgemäß geerdet sind. Benutzen Sie dann das
mit dem Gerät gelieferte Stromkabel, um es an die Srromquelle anzuschließen.
DANGER Vérifiez que les circuits de sources d'alimentation sont bien mis à la terre, puis utilisez lecordon
d'alimentation fourni avec le dispositif pour le connecter à la source d'alimentation.
PELIGRO Verifique que circuitos de la fuente de corriente están conectados a tierra correctamente; luego
use el cordón de potencia suministrado con el instrumento para conectarlo a la fuente de
corriente
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
GEFAHR Aus Sicherheitsgründen sollte ein EGB-Armband zum Schutz von elektronischen gefährdeten
Bauelementen mit einem 1 Megaohm-Reihenwiderstand ausgestattet sein.
DANGER Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga
ohm.
PELIGRO Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de 1
mega ohmio.
DANGER
Remove both power cords before servicing.
GEFAHR Trennen Sie beide Netzkabel, bevor Sie Wartungsarbeiten durchführen.
DANGER Retirez les deux cordons d'alimentation avant toute maintenance.
PELIGRO Desconecte ambos cables de alimentación antes de realizar reparaciones.
DANGER
Disconnect the power cord from all power sources to completely remove power from the device.
GEFAHR Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein
Strom zugeführt wird.
DANGER Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper
complètement l'alimentation du dispositif.
Caution and Danger Notices
Brocade DCX 8510-8 Backbone Hardware Installation Guide 179
53-1002180-10
- Brocade DCX 8510-8 1
- Backbone 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- About This Document 11
- What’s new in this document 12
- Product Overview 13
- Hardware components 14
- Port side view of the device 15
- Supported blades 17
- Chassis slots numbering 18
- Port numbering 18
- High availability 20
- Reliability 20
- Serviceability 21
- Software features 21
- Security 22
- Network manageability 22
- Device Installation 25
- Providing power to the device 29
- Cable management 29
- Possible ICL configurations 35
- Using Brocade 2 km LWL QSFPs 38
- Rack installation options 41
- Initial Configuration 43
- Configuring the IP addresses 46
- Customizing a switch name 47
- Customizing a chassis name 48
- Setting the domain ID 48
- Setting the date and time 49
- Synchronizing local time 50
- Verifying the PID mode 51
- Managing cables 54
- Powering off the chassis 56
- System Monitoring 57
- FC8-32E port blade LEDs 63
- FC8-48E port blade LEDs 64
- FC8-64 port blade LEDs 65
- FC16-32 port blade LEDs 66
- FC16-48 port blade LEDs 67
- FC16-64 port blade LEDs 68
- FCOE10-24 FCoE blade LEDs 69
- FS8-18 encryption blade LEDs 70
- FX8-24 extension blade LEDs 71
- ESD precautions 85
- Removing a chassis door 86
- Replacing a chassis door 87
- Removing a blade 90
- Replacing a blade 91
- Removing a filler panel 92
- Replacing a filler panel 93
- Faulty CP blade indicators 94
- Power-up procedure 96
- Power-down procedure 98
- Completing the replacement 102
- Time and items required 104
- 53-1002180-10 105
- Identifying power supplies 107
- Removing a power supply 107
- Replacing a power supply 108
- Removing a blower assembly 109
- Replacing a blower assembly 110
- Using the wwnrecover utility 111
- Hot-swap replacement 113
- Power-down replacement 114
- Items required 119
- Removing an SFP+ transceiver 119
- Replacing an SFP+ transceiver 120
- Removing an mSFP transceiver 121
- Replacing an mSFP transceiver 121
- Faulty chassis indicators 125
- Downloading the configuration 131
- Cable routing table 134
- Introduction 137
- Diagnostics 139
- Troubleshooting 140
- FS8-18 blade 143
- FX8-24 blade 143
- FCOE10-24 blade 145
- Port Numbering Templates 147
- 1. Blade power LED 151
- 2. Blade status LED 151
- 3. FC ports 24-47 151
- 4. FC ports 0-23 151
- 1. 10-GbE CEE ports 12-23 156
- 2. 10-GbE CEE ports 0-11 156
- 3. Power LED 156
- 4. Status LED 156
- 2. Smart card port 157
- 3. Fibre Channel ports 0-15 157
- Regulatory Statements 159
- China ROHS 160
- FCC warning (US only) 160
- VCCI statement 161
- System specifications 163
- Fibre Channel 166
- Environmental requirements 169
- Power consumption (modules) 171
- Regulatory compliance (EMC) 174
- Caution and Danger Notices 177
- Danger Notices 178
- Electrical dangers 179
- WWN bezel 186
- WWN card 186
Relacionado con productos y manuales para Hierros Brocade Communications Systems 8
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales