Brocade Communications Systems S3-1002483-03 Manual de usuario Pagina 104
- Pagina / 206
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
92 Brocade BigIron RX Series Hardware Installation Guide
53-1002483-03
Managing the interface modules
4
The <slot-number> parameter specifies the BigIron RX chassis slot number that contains the
interface module that will undergo an immediate boot. You can specify 1 – 4 for BigIron RX-4, 1 – 8
for BigIron RX-8 or 1 – 16 for BigIron RX-16.
Specifying an immediate boot from the management module’s flash memory
For example, to specify an immediate boot from the primary IronWare image in the management
module’s flash memory for the interface module installed in slot 1, enter the following command at
the Privileged EXEC level of the CLI:
BigIron RX# lp boot system mp primary 1
Syntax: lp boot system mp primary | secondary <slot-number>
The primary and secondary keywords specify the primary or secondary IronWare image in the
management module’s flash memory.
The <slot-number> parameter specifies the BigIron RX Series chassis slot number that contains
the interface module that will undergo an immediate boot. You can specify 1 – 4 for BigIron RX-4, 1
– 8 for BigIron RX-8 or 1 – 16 for BigIron RX-16.
Specifying an immediate boot from the interface module’s flash memory
For example, to specify an immediate boot from the primary IronWare image in the interface
module’s flash memory for the interface module installed in slot 1, enter the following command at
the Privileged EXEC level of the CLI:
BigIron RX# lp boot system flash primary 1
Syntax: lp boot system flash primary | secondary <slot-number>
The primary and secondary keywords specify the primary or secondary IronWare image in the
interface module’s flash memory.
The <slot-number> parameter specifies the BigIron RX Series chassis slot number that contains
the interface module that will undergo an immediate boot. You can specify 1 – 4 for BigIron RX-4, 1
– 8 for BigIron RX-8 or 1 – 16 for BigIron RX-16.
Specifying an immediate boot from a TFTP server
For example, to specify an immediate boot for the interface module installed in slot 1 from a TFTP
server, enter the following command at the Privileged EXEC level of the CLI:
BigIron RX# lp boot system tftp 123.123.123.123 primary 1
Syntax: lp boot system tftp <ip-address> <filename> <slot-number>
The <ip-address> parameter specifies the IP address of the TFTP server from which the interface
module will be booted.
The <filename> parameter specifies the name of the image from which to boot the interface
module.
The <slot-number> parameter specifies the BigIron RX Series chassis slot number that contains
the interface module that will undergo an immediate boot. You can specify 1 – 4 for BigIron RX-4, 1
– 8 for BigIron RX-8 or 1 – 16 for BigIron RX-16.
- Brocade BigIron RX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Trademark references 10
- Related publications 11
- Getting technical help 11
- Document feedback 11
- Product Overview 13
- Hardware features 14
- FIGURE 2 BigIron RX-8 chassis 15
- BigIron RX-16 chassis 16
- BigIron RX-4 17
- BigIron RX-8 18
- BigIron RX-16 18
- Management modules 19
- PCMCIA slots 20
- Console port 20
- 10/100/1000 Ethernet port 20
- Interface modules 21
- • Eight LEDs 22
- LED Position State Meaning 23
- Position State Meaning 25
- (Mini RJ 21 Copper) 26
- Switch fabric module 27
- Power supplies 28
- Cooling system 29
- • Leave the fan speed as is 31
- • Increase the fan speed 31
- • Decrease the fan speed 31
- Supported software features 32
- Installation precautions 33
- Power precautions 34
- Cabling infrastructure 36
- Installation location 37
- 2Shipping screws 38
- 1 Standard 19 inch rack 39
- Removing the slot blanks 40
- Interface modules 1 – 4 41
- 1 Management module 42
- 1 Power supply 43
- 2Power cord 44
- Final steps 45
- 2Chassis rear 48
- Interface modules 1 – 8 50
- 1Power supply 52
- 1 Lift handle 3 Power cord 53
- • “Removing the slot blanks” 57
- Interface modules 1 – 16 60
- 1Interface module 61
- 1 Lift handle 4 Ground point 64
- 3Power cord 64
- Powering-on the power source 67
- Verifying proper operation 68
- • Make certain that the 69
- • The module may not be 70
- • Check the Pwr LED on the 70
- • Enter the show chassis 70
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 73
- Assigning passwords 77
- Login lockout 78
- Password history 78
- Setting passwords to expire 78
- Configuring IP addresses 80
- Cabling a fiber optic module 85
- Cleaning fiber optic modules 86
- Testing network connectivity 88
- Configuration notes 89
- Command syntax 89
- • Terminated: The link is up 90
- • Failed: The TDR test failed 90
- Temperature Readings 93
- Misc Info 93
- Static and dynamic buffers 94
- High, 60 deg 95
- Low 57, deg. High, 70 deg 95
- Low, 67 deg. High, 80 deg 95
- • LP – An interface module 98
- Monitoring the cooling system 99
- This field... Displays 100
- 53-1002483-03 101
- BigIron RX# lp sync all 102
- Specifying an immediate boot 103
- Configuring an automatic boot 105
- BigIron RX# power-off lp 1 107
- BigIron RX# power-on lp 1 107
- BigIron RX# power-off snm 1 108
- BigIron RX# power-on snm 1 108
- Removing MAC address entries 110
- In this chapter 111
- Replacing a management module 111
- Removing a management module 112
- Replacing an interface module 116
- Removing an interface module 117
- Replacing a power supply 124
- 2 Fan assembly 128
- 1 Fan assembly 129
- • A small Allen wrench 131
- 2Filter 4Fan trap 132
- Software images required 133
- IronWare image 134
- Monitor image 134
- Boot image 134
- FPGA image 135
- Startup configuration file 135
- Displaying flash information 136
- Interface Modules 140
- Command change 144
- 02.6.00 and later 145
- TABLE 24 Image name 146
- TABLE 25 Image name 147
- Command syntax Description 148
- BigIron RX# show flash 151
- BigIron RX> show version 152
- Hitless Layer 2 OS upgrade 153
- Switchover 156
- Setting up consoles 157
- Verify the new software image 157
- BigIron RX# write memory 158
- BigIron RX# reload 158
- Dynamic configuration loading 160
- BigIron RX-if-e1000-3/1) 162
- File synchronization 163
- BigIron RX# sync-standby 164
- Scheduling a system reload 166
- Reloading at a specific time 167
- Canceling a scheduled reload 167
- Diagnostic error codes 168
- Hardware Specifications 169
- BigIron RX Series 170
- Amps Watts BTUs per hour 170
- Physical dimensions 171
- Operating environment 171
- Storage environment 171
- Safety agency approvals 171
- Port specifications 172
- Pin number MDI-X ports 173
- Regulatory Statements 175
- 에서 사용하는 것을 목적으로 합니다 176
- BSMI Statement 177
- Caution and Danger Notices 179
- Caution statements 180
- Danger notices 185
- Table 0.19: 186
- Table 0.20: 186
- Table 0.21: 186
- Software Specifications 193
- IP Multicast 195
- Management 195
- Internet drafts 196
- Cable cinch overview 197
- FIGURE 53 Two mRJ21 cables 198
- FIGURE 54 Three mRJ21 cables 199
- FIGURE 56 Five mRJ21 cables 199
- FIGURE 57 Six mRJ21 cables 200
- FIGURE 58 Seven mRJ21 cables 200
- RJ45 procedures 201
- 24 RJ45 cables in four groups 203
- 30 RJ45 cables in five groups 204
- 36 RJ45 cables in six groups 204
Relacionado con productos y manuales para Redes Brocade Communications Systems S3-1002483-03
(44 paginas)
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales