Brocade Communications Systems 825 Guía para resolver problemas Pagina 145
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Brocade Adapters Troubleshooting Guide 121
53-1002145-01
Appendix
A
Adapter BIOS and Event Message Reference
This appendix provides details on BIOS messages that display during operation of option ROM and
event messages that display during operation of adapter drivers. Included in these details are the
message, cause, and action the user should perform after viewing these messages.
Adapter BIOS messages
Table 12 provides details on BIOS-related messages generated during operation of option ROM.
The message, possible cause, and user action are provided.
TABLE 12 Adapter BIOS messages
Message Cause Recommended Action
Adapter<no> : No firmware present.
Skipping card
There is no boot firmware present on the card. Download the latest boot code file for installed
Brocade adapters from your adapter’s website.
The boot code file is designated as:
brocade_adapter_boot_fw_v<x.y.z>
where x.y.z is the version number.
Update boot code on all the adapters in the
system using instructions in the “Boot Code”
chapter of the Brocade Adapters Installation
and Reference Manual.
Adapter<no> : Version mismatch:
Card Ver<XXX>. Disabling BIOS
Current executing option ROM version is
different from the one on the adapter.
Download the latest boot code file for installed
Brocade adapters from your Brocade adapter’s
website. The boot code file is designated as:
brocade_adapter_boot_fw_v<x.y.z>
where x.y.z is the version number.
Update boot code on all the adapters in the
system using instructions in the “Boot Code”
chapter of the Brocade Adapters Installation
and Reference Manual.
Adapter<no> : No boot devices.
Disabling BIOS
BIOS on this adapter is enabled, however no
boot devices are configured.
If booting from this adapter is not required, then
ignore this message.
If booting from this adapter is required, perform
the following steps:
1 Check if boot devices are configured
through the Brocade BIOS Configuration
Utility. If not, configure devices and try
booting again.
2 In the zoning information on the switch,
verify if the target's WWN are in the same
zone as that of initiator's WWN.
- Brocade Adapters 1
- Document History 2
- Table of Contents 5
- 53-1002145-01 10
- About this Document 11
- Fabric Adapters 12
- Fabric OS and switch support 13
- Host operating system support 14
- Fibre Channel support 14
- FCoE support 15
- Ethernet support 15
- Hypervisor support 16
- What’s new in this document 17
- Document conventions 18
- Notice to the reader 19
- Additional information 20
- Providing details for support 21
- Command Function 22
- Document feedback 23
- In this chapter 25
- Gathering problem information 27
- Isolating Problems 29
- How to use this chapter 30
- General adapter problems 33
- Port link is not active 34
- BCU version mismatch warning 38
- I/O data traffic issues 39
- • If the system has only CNAs 40
- • Ignore the error message 42
- UEFI boot problems 44
- BIOS boot problems 47
- Target not visible from host 48
- Configuration menu 49
- Fabric Adapter problems 51
- HBA problems 52
- Trunking problems 53
- Cannot disable trunking 54
- CNA problems 55
- • nm-tool 57
- Teaming errors 60
- Poor network performance 63
- Non-zero VLAN IDs 64
- Recovery steps 64
- FCoE link is down 67
- DCB network problems 69
- HCM and HCM Agent problems 70
- SupportSaveController.do 71
- Javaws -viewer 73
- Javaws -uninstall 74
- Application Tool References 75
- Information Chapter 76
- Tools for Collecting Data 81
- For detailed information 82
- • Use lsmod 83
- • Use ethtool 83
- • For general driver 83
- • For network driver 83
- • (Release 1.0) 84
- • (Release 1.1 and 84
- Support Save 85
- Using BCU commands 89
- Adapter event messages 91
- TABLE 7 Event message files 92
- Host system logs 93
- HCM logs 94
- Logging levels adjustment 95
- Statistics 97
- DCB statistics (CNA only) 98
- DCB query (CNA only) 99
- FCoE statistics (CNA) 99
- Fabric statistics 100
- Firmware statistics 102
- I/O performance 103
- Logical port statistics 104
- Performance data 105
- PHY module statistics 105
- Port statistics 106
- Port Performance 106
- Remote port statistics 108
- Trunking attributes 109
- Virtual port statistics 111
- Diagnostics 113
- • Internal 114
- • External 114
- PCI loopback test 116
- Memory test 117
- Adapter temperature 118
- Queue test 118
- SCSI test 119
- Trace route 119
- Echo test 120
- Collecting BIOS data 121
- Collecting LLDP data (CNA) 121
- SFP properties 122
- Collecting port data 123
- Displaying the port log 126
- Displaying the port list 127
- Performing a port query 127
- Displaying port speed 127
- FCP-IM I/O profiling 128
- Authentication settings 129
- PHY module data 130
- QoS settings (HBA) 130
- Persistent binding 132
- Adapter properties 133
- HBA Properties 134
- Adapter queries 135
- Performance Optimization 137
- Solaris tuning 138
- Windows tuning 138
- OS tunable parameters 139
- VMware tuning 140
- Linux tuning 141
- Jumbo packet size 142
- NetQueue 142
- Adapter BIOS messages 145
- Adapter driver event messages 146
- Appendix 151
© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales