Brocade Communications Systems 825 Guía para resolver problemas Pagina 93
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Brocade Adapters Troubleshooting Guide 69
53-1002145-01
Logs
3
NOTE
Complete content for adapter driver event messages is included in Appendix A, “Adapter BIOS and
Event Message Reference”.
Logs
Event and error messages that occur during adapter, driver, and HCM operation are important tools
for isolating and resolving problems. These messages provide descriptions of an event or problem,
severity, time and date of the event, and in some cases, cause and recommended actions.
Messages are captured in logs available through HCM, BCU commands, and through host system
commands. Monitoring events and errors in these logs allows early fault detection and isolation on
a specific adapter.
Host system logs
Brocade adapter event messages are captured in host system log files. All messages related to the
Brocade adapter are identified in these logs by BFA (Brocade fabric adapter), BNA (Brocade
network adapter), and BFAL (Brocade fabric adapter library]. Table 8 describes the logs for each
supported operating system where adapter event messages display and how to view these logs.
Syslog support
You can configure the HCM Agent to forward events to a maximum of three system log destinations
using the Syslog option on the HCM Configure menu. These events will display in the operating
system logs for systems such as Solaris and Linux. For procedures to configure syslog destinations,
refer to the Brocade Adapters Administrator’s Guide.
TABLE 8 System event Logs
Operating System Log Name Location Viewing Message Log
Solaris
1
1. Brocade 804 and 1007 adapters are not supported on Solaris systems.
Syslog /var/adm/messages dmesg command
Windows Event Log Not applicable
• System category in Event
Viewer (eventvwr.exe)
• bcu winlog command
2
2. Supported on Windows systems only.
Linux Messages Log /var/log/message dmesg command
VMware
3
3. For ESX Server platforms. For Guest system, refer to information in Windows or Linux.
Messages Log /var/log/message* ,
/var/log/vmkernel*,
/var/log/vmkwarning*,
/proc/vmware/log
dmesg command
- Brocade Adapters 1
- Document History 2
- Table of Contents 5
- 53-1002145-01 10
- About this Document 11
- Fabric Adapters 12
- Fabric OS and switch support 13
- Host operating system support 14
- Fibre Channel support 14
- FCoE support 15
- Ethernet support 15
- Hypervisor support 16
- What’s new in this document 17
- Document conventions 18
- Notice to the reader 19
- Additional information 20
- Providing details for support 21
- Command Function 22
- Document feedback 23
- In this chapter 25
- Gathering problem information 27
- Isolating Problems 29
- How to use this chapter 30
- General adapter problems 33
- Port link is not active 34
- BCU version mismatch warning 38
- I/O data traffic issues 39
- • If the system has only CNAs 40
- • Ignore the error message 42
- UEFI boot problems 44
- BIOS boot problems 47
- Target not visible from host 48
- Configuration menu 49
- Fabric Adapter problems 51
- HBA problems 52
- Trunking problems 53
- Cannot disable trunking 54
- CNA problems 55
- • nm-tool 57
- Teaming errors 60
- Poor network performance 63
- Non-zero VLAN IDs 64
- Recovery steps 64
- FCoE link is down 67
- DCB network problems 69
- HCM and HCM Agent problems 70
- SupportSaveController.do 71
- Javaws -viewer 73
- Javaws -uninstall 74
- Application Tool References 75
- Information Chapter 76
- Tools for Collecting Data 81
- For detailed information 82
- • Use lsmod 83
- • Use ethtool 83
- • For general driver 83
- • For network driver 83
- • (Release 1.0) 84
- • (Release 1.1 and 84
- Support Save 85
- Using BCU commands 89
- Adapter event messages 91
- TABLE 7 Event message files 92
- Host system logs 93
- HCM logs 94
- Logging levels adjustment 95
- Statistics 97
- DCB statistics (CNA only) 98
- DCB query (CNA only) 99
- FCoE statistics (CNA) 99
- Fabric statistics 100
- Firmware statistics 102
- I/O performance 103
- Logical port statistics 104
- Performance data 105
- PHY module statistics 105
- Port statistics 106
- Port Performance 106
- Remote port statistics 108
- Trunking attributes 109
- Virtual port statistics 111
- Diagnostics 113
- • Internal 114
- • External 114
- PCI loopback test 116
- Memory test 117
- Adapter temperature 118
- Queue test 118
- SCSI test 119
- Trace route 119
- Echo test 120
- Collecting BIOS data 121
- Collecting LLDP data (CNA) 121
- SFP properties 122
- Collecting port data 123
- Displaying the port log 126
- Displaying the port list 127
- Performing a port query 127
- Displaying port speed 127
- FCP-IM I/O profiling 128
- Authentication settings 129
- PHY module data 130
- QoS settings (HBA) 130
- Persistent binding 132
- Adapter properties 133
- HBA Properties 134
- Adapter queries 135
- Performance Optimization 137
- Solaris tuning 138
- Windows tuning 138
- OS tunable parameters 139
- VMware tuning 140
- Linux tuning 141
- Jumbo packet size 142
- NetQueue 142
- Adapter BIOS messages 145
- Adapter driver event messages 146
- Appendix 151
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales