Brocade Communications Systems 825 Guía para resolver problemas Pagina 149
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Brocade Adapters Troubleshooting Guide 125
53-1002145-01
Adapter driver event messages
A
Authentication unsuccessful for base
port: WWN = [base port WWN or
MAC].
Error Network and
storage driver
2 (Port) Failure Authentication
failure.
Mismatch of
FC-SP
configuration
between switch
and HBA. Also,
check the
authentication
secret setting.
Base port enabled: Hardware
Address = [base port WWN or MAC].
Information Network and
storage driver
2 (Port) Enabled Base port enabled
by user command.
No action
required.
Base port disabled: Hardware
Address = [base port WWN or MAC].
Warning Network and
storage driver
2 (Port) Disabled Base port disabled
by user command.
No action
required.
Base port online: WWN = [Base Port
WWN].
Information Network and
storage driver
2 (Port) Online Base port logged
into fabric.
No action
required.
Base port offline: WWN = [Base Port
WWN].
Warning Network and
storage driver
2 (Port) Offline Base port logged
out of fabric.
No action
required.
Base port (WWN = [base port WWN
or MAC]) lost fabric connectivity.
Error Network and
storage driver
2 (Port) Logout Base port lost
connection with
fabric.
Check switch and
HBA
configuration.
Also, check SFP
and cable
connection
stand-up
adapters.
Heart Beat of IOC [IOC instance
number] is good.
Information Network and
storage driver
9 (TOC) Restart Successful restart
of firmware after a
failure.
No action
required.
Heart Beat of IOC [IOC instance
number] has failed.
Critical Network and
storage driver
9 (TOC) Crash Firmware not
responding.
Collect all error
information and
restart the
firmware. Invoke
bfa_supportsave.
IOC [IOC instance number] is
enabled.
Information Network and
storage driver
9 (TOC) Enabled Adapter firmware
started by user
command.
No action
required.
IOC [IOC instance number] is
disabled.
Warning Network and
storage driver
9 (TOC) Disabled Adapter firmware
stopped by user
command.
No action
required.
New adapter found: SN = [adapter
serial number] base port WWN =
[Base port WWN].
Information Network and
storage driver
1
(Adapter)
Added Adapter added to
host.
No action
required.
New SFP found: port [base port
number], Hardware Address = [Base
port WWN or MAC]..
Information Network and
storage driver
(stand-up
adapters only)
2 (Port) Found User plugged in an
SFP.
No action
required.
QOS negotiation failed for base port:
WWN = base port WWN or MAC].
Warning Network and
storage driver
2 (Port) Failure QoS negotiation
failed.
Check switch and
HBA
configuration.
TABLE 13 Driver event messages (continued)
Message Severity Event Type Category Sub
Category
Cause Action
- Brocade Adapters 1
- Document History 2
- Table of Contents 5
- 53-1002145-01 10
- About this Document 11
- Fabric Adapters 12
- Fabric OS and switch support 13
- Host operating system support 14
- Fibre Channel support 14
- FCoE support 15
- Ethernet support 15
- Hypervisor support 16
- What’s new in this document 17
- Document conventions 18
- Notice to the reader 19
- Additional information 20
- Providing details for support 21
- Command Function 22
- Document feedback 23
- In this chapter 25
- Gathering problem information 27
- Isolating Problems 29
- How to use this chapter 30
- General adapter problems 33
- Port link is not active 34
- BCU version mismatch warning 38
- I/O data traffic issues 39
- • If the system has only CNAs 40
- • Ignore the error message 42
- UEFI boot problems 44
- BIOS boot problems 47
- Target not visible from host 48
- Configuration menu 49
- Fabric Adapter problems 51
- HBA problems 52
- Trunking problems 53
- Cannot disable trunking 54
- CNA problems 55
- • nm-tool 57
- Teaming errors 60
- Poor network performance 63
- Non-zero VLAN IDs 64
- Recovery steps 64
- FCoE link is down 67
- DCB network problems 69
- HCM and HCM Agent problems 70
- SupportSaveController.do 71
- Javaws -viewer 73
- Javaws -uninstall 74
- Application Tool References 75
- Information Chapter 76
- Tools for Collecting Data 81
- For detailed information 82
- • Use lsmod 83
- • Use ethtool 83
- • For general driver 83
- • For network driver 83
- • (Release 1.0) 84
- • (Release 1.1 and 84
- Support Save 85
- Using BCU commands 89
- Adapter event messages 91
- TABLE 7 Event message files 92
- Host system logs 93
- HCM logs 94
- Logging levels adjustment 95
- Statistics 97
- DCB statistics (CNA only) 98
- DCB query (CNA only) 99
- FCoE statistics (CNA) 99
- Fabric statistics 100
- Firmware statistics 102
- I/O performance 103
- Logical port statistics 104
- Performance data 105
- PHY module statistics 105
- Port statistics 106
- Port Performance 106
- Remote port statistics 108
- Trunking attributes 109
- Virtual port statistics 111
- Diagnostics 113
- • Internal 114
- • External 114
- PCI loopback test 116
- Memory test 117
- Adapter temperature 118
- Queue test 118
- SCSI test 119
- Trace route 119
- Echo test 120
- Collecting BIOS data 121
- Collecting LLDP data (CNA) 121
- SFP properties 122
- Collecting port data 123
- Displaying the port log 126
- Displaying the port list 127
- Performing a port query 127
- Displaying port speed 127
- FCP-IM I/O profiling 128
- Authentication settings 129
- PHY module data 130
- QoS settings (HBA) 130
- Persistent binding 132
- Adapter properties 133
- HBA Properties 134
- Adapter queries 135
- Performance Optimization 137
- Solaris tuning 138
- Windows tuning 138
- OS tunable parameters 139
- VMware tuning 140
- Linux tuning 141
- Jumbo packet size 142
- NetQueue 142
- Adapter BIOS messages 145
- Adapter driver event messages 146
- Appendix 151
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales